There is no minimum thickness required for the upper crosspiece of a tzurat hapetach. For this reason, eruvin commonly use a wire or cord as the upper crosspiece.
Over the years, many different types of wire have been used for eruvin. As more practical experience accumulated, the advantages and disadvantages of each material became clearer.
Common types include:
- Nylon line
- Electrical wire
- Steel wire
- Braided cord
- Stainless-steel wire
- Builder’s line
- White or black tying cord
When choosing an eruv wire, several important factors should be considered.
1. Tensioning
The Sha’ar HaTziyun, citing the Mishkenot Yaakov, writes that care should be taken to keep the wire taut for several reasons.
In order for a wire to be tensioned properly, several factors are important:
Weight
The weight of the wire depends both on the material from which it is made and on the total length being stretched.
Surface
A smooth wire is much easier to tension across the tops of the poles. A rough wire creates friction and makes tensioning considerably more difficult.
Flexibility
A wire that is too stiff may catch or jam at the bend on top of the pole and prevent proper tensioning.
Pole-Top Design
The top of the pole must also be designed in a way that allows the wire to move freely during tensioning. This is discussed further in the section “Types of Eruv Pole Tops.”
2. Strength
There is a common misconception that the strongest possible wire is always preferable because it is less likely to break.
In practice, this is not necessarily true.
A wire that is too weak may indeed break while being tensioned or after a relatively short period of use. However, a wire that is too strong will often also be heavier and more difficult to tension.
There is another important consideration.
If a crane, tractor, truck, or other large vehicle strikes the wire, an excessively strong wire may remain intact while bending or uprooting the pole.
It is much easier to replace a broken wire than to straighten a bent pole or reinstall a pole that has been pulled out of the ground.
For this reason, the preferred wire should be strong enough for normal use but still capable of breaking under a major impact before significant damage is caused to the pole.
3. Durability
An eruv is exposed continuously to outdoor conditions, often across dozens or even hundreds of separate wire spans.
The wire therefore needs to withstand:
- Heat
- Cold
- Wind
- Rain
- Continuous exposure to sunlight
A wire that deteriorates quickly will require frequent maintenance and may invalidate the eruv if repairs are not carried out in time.
4. Practicality in the Field
Some types of wire are extremely difficult to install and repair under field conditions.
For example, stainless-steel wire may need to be laid out carefully on the ground to avoid kinks.
Wire supplied without a spool may become tangled very easily, and once tangled it can be extremely difficult to untie.
Heavy reels can also be difficult to carry together with the rest of the equipment.
This is particularly important because many eruv repairs must be carried out under time pressure on Friday, often in difficult terrain involving hills, vegetation, or limited access.
A wire that is technically strong but impractical to work with may therefore be a poor choice for routine eruv maintenance.
5. Branch Movement
Tree branches can create a serious problem when they move the wire outside the boundaries of the supporting poles.
Some types of wire become difficult to free once caught in a branch.
In addition, a very light wire can be moved easily even by relatively small branches.
Heavier and stronger wires are sometimes easier to release from branches, and their additional weight and rigidity make them less likely to be displaced by light vegetation.
6. Cost
The wire is one of the components of an eruv that experiences the most wear and requires the most frequent replacement.
Poles usually remain in place for many years, while wires are more commonly damaged or replaced.
Unfortunately, eruv maintenance often operates with limited budgets. This may be due to restricted funding from religious councils as well as limited public awareness and support.
For this reason, the selected wire should be affordable enough that a sufficient quantity can always be kept available for routine repairs.
Recommended Wire
Taking all of these considerations into account, the most commonly recommended option — and the type used in many eruvin throughout Israel — is 1.6 mm nylon line originally manufactured for fishing nets.
This line is imported into Israel primarily by organizations and suppliers involved in eruv construction and maintenance.
Advantages of Nylon Line
1. Lightweight, Smooth, and Flexible
Nylon line is light, smooth, and flexible, making it relatively easy to tension.
2. Appropriate Strength
When new, it is strong enough that it will generally not break under ordinary manual tensioning.
At the same time, if the wire is struck by a vehicle or other heavy object, the wire will usually break before causing serious damage to the pole.
After prolonged exposure to sunlight, however, nylon gradually weakens and should be monitored carefully.
3. Weather Resistance
Some nylon lines are manufactured with a UV-resistant coating.
These are relatively resistant to sunlight, rain, and wind.
Nevertheless, the wire should be inspected periodically. If it becomes dry, brittle, or visibly deteriorated from sun exposure, it should be replaced.
4. Very Practical for Fieldwork
Nylon line is especially convenient for eruv installation and repair.
It is:
- Lightweight and easy to carry
- Easy to unroll across the terrain
- Less prone to tangling when supplied on a proper spool
- Easy to lift over obstacles
- Light enough that the spool itself can sometimes be thrown over vegetation or other obstacles, provided the spool is strong enough
5. Its Main Weakness: Trees and Branches
The primary disadvantage of nylon line is its tendency to become caught in branches.
Because of its flexibility, once it becomes wrapped around or trapped in a branch, it can be difficult to release.
Even a relatively small branch may also push or pull the wire out of position.
The best way to reduce this problem is to install the wire above the height of nearby trees, using a telescopic pole where necessary.
If this is not possible, the wire should preferably be passed over the top of the tree so that it rests above the branches. When tension is applied, the wire will then rise upward.
If the wire approaches the tree from underneath, tensioning may cause it to become trapped between the branches, making it much harder to release.
In general, it is preferable for an eruv route to avoid trees wherever possible.
Where trees are unavoidable, significant and regular pruning should be carried out so that branches do not grow close to the wire.
6. Relatively Inexpensive
The line is relatively affordable, costing approximately ₪250 for 500 meters.
It is available in different spool sizes, including approximately 100-meter and 1-kilometer rolls.
From practical experience, a 500-meter spool is generally the most convenient size for fieldwork.
Other Types of Wire
The other types of wire listed above generally have disadvantages that outweigh their benefits. For this reason, the use of 1.6 mm nylon line is strongly recommended in most cases.
Nylon Line Without a Spool
In some locations, particularly fishing-supply stores in port cities, nylon line is sold without a proper spool.
This version may be slightly cheaper, but it is extremely difficult to use in the field.
One careless pull can cause the entire bundle to become tangled. Untangling it can take hours, and in many cases the remaining wire is eventually discarded.
In this situation, the cheaper product often ends up costing more in wasted time and material.
Those who are experienced in handling this type of line can transfer it onto a proper spool before using it.
Metal Wires
Various types of steel wire are generally:
- Heavy
- Difficult to tension
- Prone to rust
- More expensive
- Less practical to work with
Their main advantage is their strength and durability — at least until corrosion begins.
For most eruv applications, these wires are therefore not recommended.